|
Shunt/mV Isolation Amplifier DS 75000
- Calibrated signal setting via DIP switch
Input and output range can be set by using DIP switch – high precision without any further adjustment - High bandwidth; short response time
No signal distortion; no falsification of measured signal - Switchable Zero/Span compensation
For readjustment of the shunt/mV signal or measuring section - 3-Port isolation
Protection against erroneous measurements due to parasitic voltages or ground loops - Extremely slim design
6.2 mm slim housing for a simple and space saving DIN rail mounting - Optional In-Rail-Bus mounting rail connector
allows for fast and economical installation - Protective Separation acc. to EN 61140
Protects service personnel and downstream devices against impermissibly high voltage - 5 Years Warranty
Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant (carriage and insurance paid by sender)
|
|
DS75000
초슬림형 션트저항 / mV 신호변환기 Shunt / mV Isolation Amplifier DS 75000
양극성
및 단극성 션트저항 / mV 신호의 분리 및 변환
신호
절연증폭기 DS 75000은 션트 저항 또는 센서
전압이 낮은 기타 적용을 통해 전류 측정에
자주 사용되는 양극성 및 단극성 mV 신호의
분리 및 변환에 사용됩니다.
The Isolation Amplifier DS 75000 is used for separation and conversion of bipolar and unipolar mV-signals such as those frequently used for current measuring with shunt resistors or other applications with low sensor voltages.
입력 | 0~60mV 0~100mV
0~150mV
0~250mV
0~300mV
0~500mV | ±60mV
±100mV
±150mV
±250mV
±300mV
±500mV | 출력 | 0~20mA
4~20mA 0~10mA 2~10mA
0~10V
2~10V 0~5V 1~5V
| ±20mA
±10mA ±10V
±5V
| 전원 | 24V DC
(전원
배선 Bus 단자 옵션) | 특징 |
다양한
신호형식 입력/출력, DIP 스위치로 입력/출력 설정
및 변경 매우 빠른 응답
속도 100µs 두께
6.2mm 초슬림형, UL 인증, 방폭
(Zone 2) 인증
|
- DIP
스위치를 통한 보정된 신호 설정
DIP
스위치를 사용하여 입력 및 출력범위를
설정할 수 있습니다.
- 높은
대역폭; 짧은 응답 시간
신호
왜곡 없음; 측정된 신호의 위조 없음
- 전환
가능한 Zero/Span 보상
션트저항
/ mV
신호 또는 측정 섹션의 재조정을 위해
- 3-Port 절연
부유전압(Stray
Voltage) 또는 접지루프(Ground
Loop)로 인한 잘못된 측정으로부터
보호
- 매우
슬림한 디자인
간단하고
공간 절약을 위한 6.2mm 슬림 하우징
DIN 레일 장착
- 옵션
In-Rail-Bus 마운팅 레일 커넥터
빠르고
경제적인 설치가 가능합니다.
- EN
61140 (KS
C IEC 61140) 규격에 따른 감전보호
허용되지
않는 고전압으로부터 서비스 요원
및 후속 장치를 보호
- 5년
보증
배송일로부터
5년 이내에 발생하는 결함은 무료로 수리
또는 교환해 드립니다.
|
신호
절연증폭기(Isolation Amplifier) DS75000은 션트저항 (Shunt
Resistor) 또는 다른 낮은 센서전압을 갖는 활용분야를
통해 전류측정에 자주 사용되는 양극성 및 단극성 mV 신호의
분리 및 변환에 사용됩니다.
DS75000의
입력 및 출력 범위는 DIP 스위치를 사용하여 쉽게 설정할
수 있습니다. 보정 된 범위선택 때문에 더 이상의 조정이
필요하지 않습니다.
전면
패널의 제로/스팬 전위차계(Zero/Span Potentiometer)에서
측정범위를 전환할 수 있습니다. 또한 DIP 스위치를 사용하여
차단 주파수(Cut-off Frequency)를 측정작업에 적용할 수
있습니다.
보조전원은
연결단자 또는 옵션사양인 인레일버스(In-Rail-Bus) 커넥터를
통해 공급할 수 있습니다. 전원공급을 모니터링하기 위해
장치 전면에 녹색 LED가 제공됩니다.
The Isolation Amplifier DS 75000 is used for separation and conversion of bipolar and unipolar mV-signals such as those frequently used for current measuring with shunt resistors or other applications with low sensor voltages.
The input and output range of DS 75000 can be easily set by using DIP switch. Due to the calibrated range selection no further adjustment is necessary. A switchable compensation of the measuring range can be performed at the Zero/Span potentiometers on the front panel. Also the cut-off frequency can be adapted to the measurement task by using the DIP Switch. The auxiliary power can be supplied via the connection terminals or via the optional In-Rail-Bus connector. A green LED on the front of the unit has been provided to monitor the power supply.
Technical Data
Input
Input signal (switch selectable) | ± 60 mV, ± 100 mV, ± 150 mV, ± 250 mV, ± 300 mV, ± 500 mV 0 to 60 mV, 0 to 100 mV, 0 to 150 mV, 0 to 250 mV, 0 to 300 mV, 0 to 500 mV | Input resistance | ≥ 100 kOhm | Overload | ≤ 30 V |
Output
| Current | Voltage | Output signal (switch selectable) | ± 20 mA, 0 to 20 mA, 4 to 20 mA ± 10 mA, 0 to 10 mA, 2 to 10 mA | ± 10 V, 0 to 10 V, 2 to 10 V ± 5 V, 0 to 5 V, 1 to 5 V | Load | ≤ 12 V (600 Ohm at 20 mA) | ≤ 5 mA (2 kOhm at 10 V) | Linear transmission range | unipolar: –1 to +110 %, bipolar: –110 to +110 % | Residual ripple | < 10 mVrms |
General Data
Transmission error | < 0.1 % full scale | Temperature coefficient 1) | < 100 ppm/K | Zero/Span compensation | ± 5 % of measuring range | Cut-off frequency -3 dB | 8 kHz, switchable to 100 Hz | Response time T99 | 100 µs, 7 ms | Test voltage | 3 kV AC, 50 Hz, 1 min., Input against output against power supply | Working voltage 2) (Basic Insulation) | 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 | Protection against electrical shock 2) | Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits. | Ambient temperature | Operation Transport and storage | –25 °C to +70 °C (-13 to +158 °F) –40 °C to +85 °C (-40 to +185 °F) | Power supply | 24 V DC 9.6 V to 31.2 V, approx. 0.8 W | EMC 3) | EN 61326-1 | Approvals | UL (USA/Canada): UL 61010, Class I, Div. 2 ATEX / IECEx: Zone 2 (nA) | Construction | 6.2 mm (0.244") housing, protection class: IP 20 mounting on 35 mm DIN rail acc. to EN 60715 | Weight | Approx. 70 g |
Block
Diagram
|
Dimensions
|
|
|
Terminal assignments
1 |
+ | Input |
2 |
- | Input |
3 |
| n.c. |
4 |
| n.c. |
|
| |
5 |
+ | Output |
6 |
- | Output |
|
| |
7 |
+ | Power supply (connected to In-Rail-Bus) |
8 |
- | Power supply (connected to In-Rail-Bus) |
|
Connection Captive plus-minus clamp screws Wire cross-section max. 2.5 mm² / AWG 14 Stripped length 6 to 8 mm / 0.28 in Screw terminal torque 0.8 Nm / 7 lbf in Optional power connection via In-Rail-Bus (see accessories)
|
제품
주문 코드 Order Codes
품목 |
주문번호 |
션트
/ mV
신호
절연증폭기 DIP 스위치를 이용하여
보정된 입출력
범위 선택
In-Rail-Bus
(부속품 참조)
Shunt / mV Isolation Amplifier, calibrated range selection |
|
나사(Screw)
단자
|
푸시인(Push-in)
단자
|
Bus
단자 무 |
DS 75000 S |
DS 75004 S |
Bus
단자 유 |
DS 75000 B |
DS 75004 B |
여기에
표기된 사양들은 예고 없이 변경될 수 있습니다! (Specifications
listed here are subject to change without notice!) |