DMB96000 모드버스
RTU 연결 모듈 (Modbus RTU Connection Module DMB 96000)
인레일버스 (In-Rail-Bus) 시스템
설치용
모드버스 RTU
연결 모듈은 24V 전원과 Modbus 라인 A 및 B를 인레일버스(In-Rail-Bus)
DIN 레일 커넥터에 연결하는 데 사용됩니다.
전원
공급 장치와 Modbus 라인은 모듈의 단자(스크류 단자)에
연결됩니다. 인레일버스 DIN 레일 커넥터에 대한 연결은
후면 스프링 접점을 통해 이루어집니다. 따라서 다른 모든
DRAGO I/O 모듈은 전원 공급 장치 및 버스 라인이 있는
인레일버스를 통해 사전 배선됩니다.
DIP
스위치는 RS485 인터페이스에 일반적으로 사용되는 종단
및 분극 저항을 전환하는 데 사용할 수 있습니다. 그룹
메시지에 대해 추가 라인을 사용할 수 있습니다. (예를
들어, I/O 모듈이 지원하는 경우 그룹 오류 메시지에
대해).
특히
별도의 설치에서 추가 모듈을 연결해야 하는 경우, Modbus
RTU 연결 모듈은 피드 아웃에 사용할 수도 있습니다. 이를
위해 버스 라인용 추가 터미널이 제공됩니다.
The
Modbus RTU Connection Module is used to connect the
24 V supply and the Modbus lines A and B to the In-Rail-Bus
DIN rail connector.
The
power supply and the Modbus lines are connected to the
terminals of the module (screw terminals). The connection
to the In-Rail-Bus DIN rail connector is made via the
rear spring contacts. All other DRAGO I/O modules are
thus pre-wired via the In-Rail Bus with power supply
and bus lines.
DIP
switches can be used to switch the termination and polarization
resistors normally used for RS485 interfaces. An additional
line is available for group messages, e.g. for a group
error message, as far as this is supported by the I/O
modules.
The
Modbus RTU connection module can also be used for feed
out, especially if further modules are to be connected
in separate installations. Additional terminals for
the bus lines are provided for this purpose.
Technical Data
General Data
Supply
voltage
|
24 V DC,
0.3 W, Voltage range 16.8 to
31.2 V
|
Input
current
|
≤ 4.5
A
|
Recommended
fuse
|
5 A slow-blow
|
Voltage
drop
|
≤ 0.2
V
|
Indication
LEDs
|
Operating
and fault: green/red Modbus
communication: yellow
|
Ambient
temperature
|
Operation:
-25 °C to +70 °C (-13
to +158 °F) Transport
and storage: -40 °C to +85
°C (-40 to +185 °F)
|
EMC
|
EN 61326-1
|
Construction
|
6.2
mm (0.244") housing, protection
type: IP 20, mounting on 35
mm DIN rail acc. to EN 60715
|
Connection (captive
plus-minus clamp screws)
|
Solid:
0.5 mm² - 4 mm² /
AWG 20-12 Fine-stranded:
0.5 mm² - 2.5 mm²
/ AWG 20-14 Stripped length:
6-8 mm / 0.28 in Screw terminal
torque 0.8 Nm / 7 lbf in
|
Weight
|
Approx.
70 g
|
Block diagram

Dimensions
|
Terminal assignments
|

|
1 |
Modbus
A
| |
3 |
Group
Message (GM)
|
2 |
Modbus
B
| |
4 |
GND
|
|
|
|
|
|
5 |
Modbus
A
| |
7 |
24V
Supply
|
6
|
Modbus
B
|
|
8
|
GND
|
A |
Modbus
A
|
B |
Modbus
B
|
C- |
24V
(-) Supply
|
D+
|
24V
(+) Supply
|
E
|
Group
Message (GM) |
|

품목
|
주문번호 |
DMB96000
모드버스 RTU 연결 모듈 Modbus RTU Connection
Module DMB 96000
|
나사(Screw)
단자
|
푸시인(Push-in)
단자
|
DMB
96000B
|
DMB
96004B
|
여기에
표기된 사양들은 예고 없이 변경될 수 있습니다! (Specifications
listed here are subject to change without notice!)
|