드라고 신호변환기      DRAGO Signal Converters

측정, 제어, 자동화를 위한 산업용 신호처리, DRAGO가 합니다.

페이지

Homepage

제품군

Product Line

제품소개

Products

신호변환기 선정 가이드

Selection Matrix

제품 전체 보기

Service Web Portals

내려받기

Downloads

제품 및 구입 문의

Contact

DH11000

Loop-Powered (Passive) Isolator DH 11000

 

  • Galvanic isolation across input and output
    Protection against erroneous measurements due to parasitic voltages or ground loops
  • No power supply required
    Saving costs since wiring is reduced and line influences are omitted
  • Extremely slim design, 1- and 2-channel versions
    Only 3.1 mm DIN-rail per channel
  • Protective Separation acc. to EN61140
    Protects service personnel and downstream devices against impermissibly high voltage
  • Maximum reliability
    No maintenance costs
  • 5 Years Warranty
    Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant (carriage and insurance paid by sender)

DH11000 초슬림형 루프파워 (무전원) 신호 아이솔레이터
Loop-Powered (Passive) Isolator DH 11000

0(4) ~ 20mA 산업용 표준 전류 신호의 분리 및 절연

입력 루프 전원 절연기 DH 11000은 측정 신호를 높은 정확도로 출력으로 전송하면서 0 (4) ~ 20 mA 표준 신호에 대해 갈바닉 절연을 제공합니다.

The input loop-powered isolator DH 11000 provides galvanic sepa­ration for 0(4) to 20 mA standard signals, while trans­ferring the measure­ment signal to the output with a high degree of accuracy.

입력

0 ~ 20mA     4 ~ 20mA

출력

0 ~ 20mA     4 ~ 20mA

전원

무전원 (Input Loop-Powered)

특징

두께 6.2mm 초슬림형, UL 인증, 방폭 (Zone 2) 인증
1채널 / 2채널 옵션

  • 입력 및 출력 간의 갈바닉 절연
    부유
    전압(S
    tray Voltage) 또는 접지루프(Ground Loop)로 인한 잘못된 측정으로부터 보호
  • 전원 공급이 필요하지 않습니다.
    배선이 줄어들고 선로 영향이 생략되므로 비용 절감
  • 매우 슬림한 디자인, 1 및 2채널 버전
    채널당 단 3.1mm DIN 레일
  • EN 61140 (KS C IEC 61140) 규격에 따른 감전보호
    허용되지 않는 고전압으로부터 서비스 요원 및 후속 장치를 보호
  • 최대 신뢰성
    유지 보수 비용 없음
  • 5년 보증
    배송
    일로부터 5년 이내에 발생하는 결함은 무료로 수리 또는 교환해 드립니다.

입력 루프전원 신호절연기(Input Loop-powered Isolator) DH11000은 측정신호를 높은 정확도로 출력으로 전송하면서 0(4) ~ 20mA 표준신호에 대해 갈바닉 분리(Galvanic Isolation)를 제공합니다.

이 신호절연기는 간섭전압(Interference Voltage)이 계속 이어지는 것을 방지하고 부유 노이즈(Parasitic Noise)를 효과적으로 억제합니다. 2.3V의 매우 낮은 전압강하와 높은 정확도가 함께 작동하여 DH11000을 시스템 설계에서 첫 번째로 선택하게 합니다.

지능형 설계와 그에 따른 고도로 집적된 부품의 필수적인 방지기능은 측정신호의 왜곡 없이 매우 긴 수명과 신뢰성을 제공합니다.

DH11000은 보조전원이 입력신호에서 왜곡되지 않고 얻어지므로 추가 전원공급이 필요하지 않습니다. 이는 설치 중에 비용을 절감 할뿐만 아니라 신뢰성을 높입니다.

The input loop-powered isolator DH 11000 provides galvanic sepa­ration for 0(4) to 20 mA standard signals, while trans­ferring the measure­ment signal to the output with a high degree of accuracy.

The unit avoids interference voltage carry-over and effectively suppressing parasitic noise. The very low drop voltage of 2.3 V and the high level of accuracy work together to make the DH 11000 the first choice in system design.

Intelligent design and their consequential avoidance of highly integrated components result in extremely long service lives and reliability - without any falsification of the measurement signal.

The DH 11000 requires no additional power supply since the auxiliary power is obtained from the input signal without distorting it. This not only saves costs during installation, but also increases reliability.

활용 예:  입력 루프파워 (Input Loop-Powered) 0(4)~20mA 신호 아이솔레이터

DH11000

 

Technical Data

Input

Input Signal0(4) to 20 mA
Operating current< 200 µA
Voltage drop< 2.3 V
Overload≤ 50 mA, 30 V

 

Output

Output signal0(4) to 20 mA
Load600 Ohm
Cut-off frequency -3 dB100 Hz
Response time T995 ms
Residual ripple< 10 mVrms

 

General Data

Transmission error< 0.1 % full scale
Load error< 0.05 % of measured value / 100 Ohm load
Temperature coefficient 1)< 100 ppm/K
Test voltage3 kV AC, 50 Hz, 1 min. all circuits against one another
Working voltage 2)
(Basic Insulation)
Up to 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1
Protection against electrical shock 2)Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits.
Ambient temperatureOperation
Transport and storage
–25 °C to +70 °C   (-13 to +158 °F)
–40 °C to +85 °C   (-40 to +185 °F)
EMC 3)EN 61326-1
ApprovalsUL (USA/Canada): UL 61010, Class I, Div. 2
ATEX / IECEx: Zone 2 (nA)
Construction6.2 mm (0.244") housing, protection class: IP 20
mounting on 35 mm DIN rail acc. to EN 60715
WeightApprox. 70 g
  1. Average TC related to full scale value in specified operating temperature range, reference temperature 23 °C
  2. For applications with high working voltages, ensure there is sufficient spacing or isolation from neighboring devices and protection against electric shocks.
  3. Minor deviations possible during interference

 

Block Diagram

Dimensions

DH11000

DH11000


Terminal assignments

1

+

Input I

5

+

Output I

2

-

Input I

6

-

Output I

 

 

 

 

 

 

3

+

Input II

7

+

Output II

4

-

Input II

8

-

Output II

Connection
Captive plus-minus clamp screws
Wire cross-section max. 2.5 mm² / AWG 14
Stripped length 6 to 8 mm / 0.28 in
Screw terminal torque 0.8 Nm / 7 lbf in

 

 

제품 주문 코드   Order Codes

품목

주문번호

루프 전원 신호절연기

Loop-Powered Isolator

 

나사(Screw) 단자

푸시인(Push-in) 단자

1채널

DH 11010 S

DH 11014 S

2채널

DH 11020 S

DH 11024 S

 
여기에 표기된 사양들은 예고 없이 변경될 수 있습니다! (Specifications listed here are subject to change without notice!)
© Copyright 2004-2024 by DRAGO Automation GmbH

드라고 신호변환기 한국판매원 - 에이콤 (AKORM Corp.)