드라고 신호변환기      DRAGO Signal Converters

측정, 제어, 자동화를 위한 산업용 신호처리, DRAGO가 합니다.

페이지

Homepage

제품군

Product Line

제품소개

Products

신호변환기 선정 가이드

Selection Matrix

제품 전체 보기

Service Web Portals

내려받기

Downloads

제품 및 구입 문의

Contact

DC52500

Repeater Power Supply HART DC 52500

 

  • Universal operation of SMART Transmitters
    Energization and separation of field located 2-, 3- and 4-wire transmitters
  • Bidirectional HART transmission
    HART data transfer for repeater and isolator operation
  • 3-Port isolation
    Protection against erroneous measurements due to parasitic voltages or ground loops
  • Extremely slim design
    6.2 mm slim housing for a simple and space saving installation
  • Optional In-Rail-Bus mounting rail connector
    allows for fast and economical installation
  • Protective Separation acc. to EN 61140
    Protects service personnel and downstream devices against impermissibly high voltage
  • 5 Years Warranty
    Defects occurring within 5 years from delivery date shall be remedied free of charge at our plant (carriage and insurance paid by sender)

DC52500 초슬림형 하트 통신 2 / 3선식 트랜스미터 전원공급기
Repeater Power Supply HART DC 52500

HART 통신 기능이 있는 2 / 3선식 SMART 신호전송기(트랜스미터)에 전원 공급 및 출력 신호의 절연

HART Repeater 전원 공급기 DC 52500은 압력/유량/레벨 등 2선식또는 3선식 SMART 트랜스미터에 전원을 공급하고, 이 센서에서 생성되는 신호를 받아내며, 또한 이 신호을 절연(Isloation)하는데 사용됩니다.

The Repeater Power Supply DC 52500 is used to supply and separate 2- and 3-wire SMART Transmitters and active sensor signals with HART communication.

입력

4 ~ 20mA   with HART

2선식 트랜스미터 전원 공급 및 신호 입력

3선식 트랜스미터 전원 공급 및 신호 입력

출력

4 ~ 20mA with HART

전원

24V DC (전원 배선 Bus 단자 옵션)

특징

2/3/4선식 HART 트랜스미터 신호 입력/출력
두께 6.2mm 초슬림형, UL 인증, 방폭 (Zone 2) 인증

  • SMART 송신기의 범용 작동
    현장에서 2, 3 및 4선식 송신기의 에너지 공급 및 분리
  • 양방향 HART 전송
    R
    epeater 및 절연기 작동을 위한 HART 데이터 전송
  • 3-Port 절연
    부유
    전압(S
    tray Voltage) 또는 접지루프(Ground Loop)로 인한 잘못된 측정으로부터 보호
  • 매우 슬림한 디자인
    간단하고 공간 절약적인 설치를 위한 6.2mm 슬림형 하우징
  • 옵션 In-Rail-Bus 마운팅 레일 커넥터
    빠르고 경제적인 설치가 가능합니다.
  • EN 61140 (KS C IEC 61140) 규격에 따른 감전보호
    허용되지 않는 고전압으로부터 서비스 요원 및 후속 장치를 보호
  • 5년 보증
    배송일로부터 5년 이내에 발생하는 결함은 무료로 수리 또는 교환해 드립니다.

신호중계기(Repeater) 전원공급 장치 DC52500은 HART 통신을 사용하는 2선식 및 3선식 SMART 신호전송기에 전원을 공급하고 활성 센서신호를 분리하는데 사용됩니다.

신호전송기에 전원을 공급하고 출력에 갈바닉 절연(Galvanic Isolated) 고정밀 측정신호를 전송합니다. 다른 방법으로 측정 입력은 4선식 신호전송기에서 0/4 ~ 20mA 활성신호를 받아들입니다.

아날로그 신호 외에도 DC52500은 HART 통신을 위한 데이터 프로토콜을 전송합니다. 그것은 배선의 모든 지점에서 필드 장치와 양방향 통신이 가능합니다.

보조전원은 연결단자 또는 옵션사양인 인레일버스(In-Rail-Bus) 커넥터를 통해 공급할 수 있습니다. 전원공급을 모니터링하기 위해 장치 전면에 녹색 LED가 제공됩니다.

The Repeater Power Supply DC 52500 is used to supply and separate 2- and 3-wire SMART Transmitters and active sensor signals with HART communication.

It supplies the transmitter with power and transmits the measuring signal with high accuracy galvanic isolated to the output. Alternative the measuring input accepts active 0/4 to 20 mA signals from 4-wire transmitters.

In addition to the analog signal, the DC 52500 also transmits data protocols for HART communication. It allows bidirectional communication with the field device from every point of the cabling.

The auxiliary power can be supplied via the connection terminals or via the optional In- Rail-Bus connector. A green LED on the front of the unit has been provided to monitor the power supply.

 

Technical Data

Input

Input signal0/4 to 20 mA(4 to 20 mA with HART signal)
Input resistance≤ 50 Ohm 
Over load50 mA / 30 V 
Transmitter supply (Tx)16 V (open circuit voltage/short circuit current < 22 V/35 mA)
Communication signalBidirectional HART transmission, internal AC impedance 250 Ohm

Output

Output signal0/4 to 20 mA(4 to 20 mA with HART signal)
Load0 to 600 Ohm (at 20 mA)(230 Ohm to 600 Ohm with HART signal)
Linear transmission range–1 to +110 %
Residual ripple< 10 mVrms

General Data

Transmission error< 0.1 % full scale
Temperature coefficient 1)< 100 ppm/K
Cut-off frequency -3 dB100 Hz,     > 2.5 kHz  HART signal
Response time T997 ms
Test voltage3 kV AC, 50 Hz, 1 min, Input against output against power supply
Working voltage 2)
(Basic Insulation)
600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1
Protection against electrical shock 2)Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2
Ambient temperature Operation
Transport and storage
–25 °C to +70 °C   (-13 to +158 °F)
–40 °C to +85 °C   (-40 to +185 °F)
Power supply24 V DC, voltage range 16.8 V to 31.2 V DC, approx. 1.3 W
EMC 3)EN 61326-1
ApprovalsUL (USA/Canada): UL 61010, Class I, Div. 2
ATEX / IECEx: Zone 2 (nA)
Construction6.2 mm (0.244") housing, protection class: IP 20
mounting on 35 mm DIN rail acc. to EN 60715
WeightApprox. 70 g
  1. Average TC related to full scale value in specified operating temperature range, reference temperature 23 °C
  2. For applications with high working voltages, ensure there is sufficient spacing or isolation from neighboring devices and protection against electric shocks.
  3. Minor deviations possible during interference

 

Block Diagram

Dimensions

DC52500

DC52500


Terminal assignments

1

+

Transmitter supply voltage UTx

2

+

Input current

3

-

Input GND

4

 

n.c.

 

 

 

5

+

Output

6

-

Output

 

 

 

7

+

Power supply (connected to In-Rail-Bus)

8

-

Power supply (connected to In-Rail-Bus)

Connection
Captive plus-minus clamp screws
Wire cross-section max. 2.5 mm² / AWG 14
Stripped length 6 to 8 mm / 0.28 in
Screw terminal torque 0.8 Nm / 7 lbf in
Optional power connection via In-Rail-Bus (see accessories)

 

 

제품 주문 코드   Order Codes

품목

주문번호

양방향 HART 데이터 전송 중계기 전원공급기

In-Rail-Bus (부속품 참조)

Repeater Power Supply, bidirectional HART Data transmission

 

나사(Screw) 단자

푸시인(Push-in) 단자

Bus 단자 무

DC 52500 S

DC 52504 S

Bus 단자 유

DC 52500 B

DC 52504 B

 
여기에 표기된 사양들은 예고 없이 변경될 수 있습니다! (Specifications listed here are subject to change without notice!)
© Copyright 2004-2024 by DRAGO Automation GmbH

드라고 신호변환기 한국판매원 - 에이콤 (AKORM Corp.)